1991 Mustang Sport Sedan weld subframe connectors


Finished up the Welding, check out the two videos below!

Now that the welding of the sub frame connectors, battle boxes and torque plates is complete - all that I have to do now is: replace complete powertrain (5.0 EFI destroked), swap compete interior (black from my 1993), upgrade all electrics (alternator, cooling system, etc), front end will get all re-done with 2" drop spindles, bilstien struts, FMS convertible springs, a host of MM parts... braking system will be upgraded similar to 1993 cobra type correct offset rear, 2000 watt stereo system... and figure out the 11' hydraulic clutch system I am putting together {WHEW!!} after that I will have to get the car inspected, licenced, smogged and registered $$$ holy moly...


Back to PAGE ONE: Weld Battle Box, Torque Plates
1991_Mustang_Coupe_1.jpg
1991_Mustang_Coupe_1.jpg
275.75 KB
1991_Mustang_Coupe_2.jpg
1991_Mustang_Coupe_2.jpg
342.98 KB
1991_Mustang_Coupe_31.jpg
1991_Mustang_Coupe_31.jpg
287.53 KB
1991_Mustang_Coupe_32.jpg
1991_Mustang_Coupe_32.jpg
288.92 KB
1991_Mustang_Coupe_40.jpg
1991_Mustang_Coupe_40.jpg
295.48 KB
1991_Mustang_Coupe_41.jpg
1991_Mustang_Coupe_41.jpg
385.03 KB

This section shows welding on a rear point of the connectors to the subframe there is a video with sound.
1991_Mustang_Coupe_51.jpg
1991_Mustang_Coupe_51.jpg
337.92 KB
1991 Mustang Coupe
1991_Mustang_Coupe_77.jpg
1991_Mustang_Coupe_77.jpg
328.74 KB
Welding Subframe Video
Welding Subframe Video 12.12 MB
VIDEO!

Grog noticed a space on the front of the connectors, he placed a grade 8 washer in the void, welded up the gap, check out the video with sound..connectors to the subframe there is a video with sound.
1991_Mustang_Coupe_87.jpg
1991_Mustang_Coupe_87.jpg
290.91 KB
1991_Mustang_Coupe_87a.avi
Welding Front Subframe Video 7.86 MB
VIDEO!
1991_Mustang_Coupe_88.jpg
1991_Mustang_Coupe_88.jpg
288.82 KB
1991_Mustang_Coupe_89.jpg
1991_Mustang_Coupe_89.jpg
180.50 KB

This section shows the finished product of 5 pieces of metal sections welded onto each side of this fox mustang... focusing on the rear where plates were welded to provide a flat area to weld up the partial places that are incorporated into these long full length boxed subframe connectors. I have not seen anybody use this combination of parts, I hope you get ideas from what I have done here, thanks!
1991_Mustang_Coupe_90.jpg
1991_Mustang_Coupe_90.jpg
291.48 KB
1991_Mustang_Coupe_91.jpg
1991_Mustang_Coupe_91.jpg
252.66 KB
1991_Mustang_Coupe_92.jpg
1991_Mustang_Coupe_92.jpg
212.83 KB
1991_Mustang_Coupe_93.jpg
1991_Mustang_Coupe_93.jpg
324.90 KB
1991_Mustang_Coupe_94.jpg
1991_Mustang_Coupe_94.jpg
342.03 KB
1991_Mustang_Coupe_95.jpg
1991_Mustang_Coupe_95.jpg
291.20 KB

www.thatmetalbox.com home